• Differential Probe 1:10/100, 100 MHz, 700V
  • 4233 Differential Probe Discontinued See PT-8101

    • 4233 Differential Probe Discontinued See PT-8101

    $0.00
    (No reviews yet) Write a Review
    Width:
    8.00 (in)
    Height:
    3.00 (in)
    Depth:
    11.00 (in)

    Product Description

    Differential Probe for Power management- Model 4233  (Discontinued -Suggested replacement Model PT-8101)

    The 4233 meets EN61010 Category III Requirements. With wide choice of attenuation
    ration, the 4233 is capable of making full range (from millivolts to + 700V) measurements of
    floating signals in power electronic circuits.

    Features
    -Up to +/-1400 V(DC + Peak AC) Differential and Common Mode
    -Safety Certified-Bandwidth up to 100 MHz

    Applications
    -Switching Power Supply Design
    -Motor Drive Design
    -Electronic Ballast Design
    -CTR Display Design

    Included
    -Black Storage Box
    -Red & Black Sprung Hooks
    -Calibration Certificate
    -4ea AA Batteries
    -9 VDC Adapter

    		 Product image

    Calibration Procedures

    User Manual

    Technical Data Sheet

     

    Optional 4200 Series Accessories

     

    blackbox.jpg
    Included with Probe
    Black Storage
    Box
    &
    9VDC Adapter
    4210-new.jpg
     
     
     
     
     
     
     
     
     

     

    4233 Specifications

    Bandwidth DC to 100 MHz (-3dB)
    Attenuation 1:10/100
    Accuracy +/-2%
    Rise Time 3.5ns
    Input Impedance 4Mohm //7pF each side to ground
    Input Voltage
    -Category
    - Differential Range*

    -Common Mode Range*
    -Absolute Max. Voltage*(Differential or Common Mode)
    CAT III
    70Vrms and +/- 70V(DC + Peak AC @ 1/10
    700Vrms and +/- 700V(DC + Peak AC) @ 1/100
    700Vrms and +/- 700V(DC + Peak AC) @ 1/10 & 1/100
    1000Vrms and +/-1000V(DC + Peak AC) @ 1/10 & 1/100
    Output Voltage

    - Swing (into 50 kohm load
    -Offset (typical)
    -Noise (typical)
    - Source Impedance

     +/-7V
    <+/-5m
    V0.9m Vrms
    50 ohm (for using 1 Mohm input system oscilloscope)
    CMMR (typical) -85dB @ 50Hz, -55dB @ 1MHz
    Ambient Operating Temperature -10 to 40 degree centigrade
    Ambient Storage Temperature -30 to 70 degree centigrade
    Ambient Operating Humidity Up to 85% RH
    Ambient Storage Humidity Up to 85% RH
    Power Requirements** -Standard-options 4 x AA cells or 9 VDC 120mA mains adapter (Both included)
    -Optional- Power Leads Power Leads
    Length of BNC Cable 36"
    Length of Input Leads 12"
    Weight 0.9 lb
    Dimensions 8" x 3 1/4" x 1 1/2"

    *Voltage limit is the lesser of the DC + Peak AC and RMS values.**
    a. The supplied voltage must be less than 12V and greater than 4.4V, otherwise the probe could be damaged or will not operate properly.
    b. polarity is "+" inside and "V" outside. For wrong polarity, built-in circuit protects the probe, no danger or damage will occur.
    c. When the voltage of the cells become too low, the power indicator on the panel will flicker. Additional Accessories- Shown Below

    Product Videos

    Custom Field

    Product Reviews

    Write a Review